陳佳佳 wrote:
想購買kodak v...(恕刪)
今天又找到一間柯達有賣v1253(還是要直接下訂單購買)......$7900..不過沒有送記憶卡>"<
前天問一間柯達直接下單........$8500
還看到一間燦坤有賣.....$9900........什麼都沒送
柯達的相機不是都跟公司訂嗎？！為什麼價錢差那麼多？
我在想要不要過年後再買，會不會有可能又降價呢？
(可是也有可能到時訂不到貨XD)
個人積分：0分
文章編號：4771102
個人積分：338分
文章編號：4772683
個人積分：0分
文章編號：4775398
RAIN LIN wrote:
最近買了Kodak ...(恕刪)
Download and Extract the Firmware File
1. Download the file to your computer.
2. Double-click the file to start the WinZip Self-Extractor.
3. Select Unzip to folder, and specify a locetion, or leave the default locetion.
4. Click Unzip. The firmware file unzips to the specified folder.
5. Note the locetion of the folder. The file has a .pak file extension.
6. Close the WinZip Self-Extractor.
Select a Method
* If you do not have a memory card and card reader, use Method 1.
* If you have a memory card and a card reader, use Method 1 or Method 2.
Method 1
1. Visit the EASYSHARE Software Web page at www.kodak.com/go/easysharesw, and download the latest version of software.
NOTE: EASYSHARE Software version 6.x or later must be used during this procedure.
2. Connect the camera to your computer using a USB cable.
NOTE: The first time you connect your camera to your computer, Sync and Transfer Setup or Sync and Transfer Assistant prompts appear on the screen. Follow the prompts to set up the camera as a device in the software.
3. Remove the memory card from the camera.
4. Turn on the camera.
5. Start EASYSHARE Software.
6. Select Tools > Sync and Transfer Manager.
7. Select your device from the list in the left column, and then select the Info tab.
8. Click Update Firmware, and go to the locetion where you downloaded the firmware file.
9. Click Open to copy the file from your computer to the internal memory on the camera.
10. Turn off the camera, and then disconnect the USB cable from the camera.
11. Turn on the camera and follow the on-screen instructions to complete the upgrade. The upgrade takes approximately two minutes. When it is complete, the camera will delete the firmware file from internal memory.
12. Turn off the camera, and then turn it back on again.
Method 2
1. Remove the files from the memory card.
2. Place the memory card in the card reader.
3. Open the drive corresponding to the memory card to view the card contents.
4. Check that a System folder exists on the memory card. If not, create one.
5. Locate the firmware file on your computer and copy it into the System folder on the memory card.
6. Remove the memory card from the card reader, and insert the memory card into the camera.
7. Turn off the camera.
8. Turn on the camera and follow the on-screen instructions to complete the upgrade. The upgrade takes approximately two minutes.
9. Turn off the camera, and then turn it back on again.
個人積分：0分
文章編號：4906193
個人積分：338分
文章編號：4906679
個人積分：15分
文章編號：4910616
個人積分：0分
文章編號：4920355
個人積分：0分
文章編號：4936727
個人積分：0分
文章編號：4939735
個人積分：0分
文章編號：4942037
