Part I. DD-WRT vs OpenWRT
AP1:TP-Link 1043NDv1
FW:OpenWRT
角色:WDS AP( 連Internet GW)
AP2:TP-Link 841NDv8
FW:DD-WRT
角色:WDS Client
TP-Link 1043NDv1 ((((..WDS..))))TP-Link 841NDv8 WDS之間連線速度
WDS AP對 WDS Client (本地端測試,距離1M)
WDS角色定位/SSID/通道/加密編碼(AES)方式
http://i.imgur.com/Ytd83mSl.png
WDS終端(第二台(含)以後的AP) 跑Site Suvery瀏覽/掃描區域熱點/無線AP.選擇正確的SSID-> Join加入
WDS角色定位頻寬40MHz/WIFI區碼相同
http://i.imgur.com/JPtRZcsl.png
WDS終端 定義上層WDS AP的MAC為GW,選擇LAN 橋接模式
Spanning Tree(STP協定服務->開啟) 預防線路Loop,主從兩台都需開啟。
WD Client(第二台以後AP)指定上層WDS AP的IP位址為GW。
WD Client(第二台以後...AP)
關閉:DNS MASQ服務
關閉:DHCP服務
全部延伸訊號讓第一台AP集中控管
+入NTP校時以便對System Log有正確的寫入時間
以ICMP從第一台的PC ping 第二台WD Client無Error
第一台主AP設定好在設定好第二台...第N台...第N台相同設定方法。
移置WDS終端到指定地點,測試連線,搞定。
================================================================
PartII. Gargoyle v.s OpenWRT
AP1:TP-Link 1043NDv1
FW:OpenWRT
角色:WDS AP( 連Internet GW)
AP3:TL-WR941NDv5
FW:Gargoyle
角色:WDS Client
Connection =>
選 "Wireless Bridge/Repeater"下面的選單就全變
指定這台 WDS Staion的IP/子網路遮罩/Gw IP,GW就是那台WDS AP
DNS Server也指到WDS AP,
SSID to Join:點選SCAN 按鍵,會出現下拉選單,指定到哪台WDS AP.
SSID密碼設定正確,WDS網路就通啦
Gargoyle FW還真是簡單效率,一頁WWW搞定
峰值
優化設定
強制40MHz=> 打勾拿掉,讓3G手機使用正常(只能跑20MHz),而且40MHz+20MHz雙頻寬使用反而速度優化
訊號覆蓋率峰值:84%(起碼70%以上)
Singal峰值: 接近-50dbm(超強) 大概在-60dbm以下
Bitrate + Tx/Rx峰值:240幾 Mbit/s (八成)
看起來WR1043NDv1 搭配 WR-941NDv5 跑起來效能不差,是硬體的功勞? 還是 FW的功勞?
難道這兩台是兄弟機?
個人積分：102分
文章編號：53989461
Version 1.7.0, based on OpenWRT Barrier Breaker is now officially released.
Do NOT try to preserve settings between previous releases and 1.7.0 -- The new configuration files for Barrier Breaker are different than previous versions of OpenWRT and you will likely brick your router!
This released focused merely on updating the functionality available on 1.6.2 to run on the more recent version of OpenWRT, and the primary benefit you will see is newer wireless drivers and the availability of Gargoyle for a much larger range of router models.
One important note: Wireless AC capability is not supported in this release. The hardware of some supported models has this capability, but software support is currently not available for Gargoyle.
There was a recent patch contributed that will enable guest network support -- that is not included in this release, but now that porting to Barrier Breaker is complete this will be merged and will be available in the next release.
This release marks the first release in a the new 1.7.x Experimental branch, and may be buggier than previous releases in the 1.6.x stable branch. I have tried to test well, but I anticipate there may be a few bugs remaining. Please report any bugs -- in particular bugs that were not present in previous releases -- in the thread below.
Eric
新版本 刷新
