Brompton清漆的耐用度較差嗎?

我是買09年的清漆款
可是 我的車會不停的有氣泡 然後就掉漆(透明層)...
不知道是不是不正常的狀況...
這樣的情況 越來越多....
請問各位09年的清漆有相同的狀況嗎?
ebear0301 wrote:
您是說,我們買的有上漆的小布的管材,是狀況不好的喔?!! 天啊!...

不會吧. 要是真的"狀況不好", 是不會拿來做車子的. 他們不是那種會偷工減料的文化啦...
應該是說管子顏色花紋好看乾淨的就拿來做清漆. 燒的顏色有點髒的就上漆. 這樣吧?

to ShenWey,
銅焊每台都是, 請看他們的官網;http://www.brompton.co.uk/page.asp?p=3088
有關清漆的其它, 我在 yahoo 的知名 brompton group 找到以下. 這是在說09年以前的就是了:

"The raw frame is bristled/brushed but not polished, a quite elaborated process, than zinc-phosphete.
Than to get its final finish and protection the 'raw' frame is lacquered with a clear coat.
(clear) lacquer = (clear) coat = a shinyish finishing layer of (transparent) (mosttimes robust) paint.
BTW
Other Bromptons have to do without such a clear coat finish, their main and only paint being quite robust has to withstand all weather and dirt coming its way, it normally does a good job. Since (an extra) clear coat would add quite some extra weight/cost to the bike, without making it significantly better, Brompton always choose to have one kind of coat to do the whole job.
Knowing the nature of the bikes use that demands quite an high quality, and thus very thorough control, the latter being one of the reasons of recent (extra) delays, if the paintwork doesn't meet the (technical) standard the frame is rejected and stripped to be refinished (which takes a lot of time)."

"You can't "touch-up" powdercoated metal with the same kind of finish as the original. Powdercoating, including clear powders, are spray applied dry under air pressure while the receiving object is electrostatically charged. The object is then baked in an oven hot enough to cause the powder to melt onto the prepared metal surface (the powder is really a pigmented plastic material, commonly polyester but others are possible.)
You can touch up small areas with a solvent-based paint as long as the surface is clean of rust or dirt. More extensive damage may require an entire re-coating after removal of the old powder finish. Removal is typically done by abrasive grit blasting."

Touching up - 也有很多人建議就用透明指甲油, 或是模型店的 clearcoat enamel
這話題跟主題無關
小布空運來台嗎?
這運費比海運多幾倍
jienguanliyuan
小小弟淺見

不管是08或09的清漆

都有它獨特的特性 如果用了幾年後 他繼續惡化

我會把他全拆了 送去工廠重新上漆

孰不知 台灣的噴漆技工 也挺強的

所以囉 買車也是買緣分對吧

sam570729 wrote:
小小弟淺見不管是08...(恕刪)

可是我才買兩個月不到
已經開始起泡 掉漆了....
本身這款車就都是這樣嗎...
那清漆用久掉漆最終會變什麼顏色呢
昨日的浪子~柯林髮落, 今日的巨星~球德洛, 明日的傳奇~褲濕啦 , 永遠的女神~愛田由
清晰版的銅焊是很漂亮
而要造成這種效果,
材質先上漆然後銅焊,就是這種效果。
(有興趣的自己實驗一下即知)

然而銅焊接時要去除雜質,需用硼砂。
焊接完處理不完全,油漆會脫落
焊接時,未焊接觸冷卻包覆不完全時,原有油漆會受熱起泡

這是小弟的淺見。
有沒有車主願意提供各種不同狀況的照片呢?
(不然感覺形容的有點抽象)謝謝!
CoolJason wrote:
可是我才買兩個月不到...(恕刪)


我朋友的不會喔,你應該買到瑕疵品吧,因為當初陪他一起挑車,其中有一台就有起泡情形,不知你車子的照片可否po上來,讓我們幫你看一下
昨日的浪子~柯林髮落, 今日的巨星~球德洛, 明日的傳奇~褲濕啦 , 永遠的女神~愛田由
文章分享
評分
評分
複製連結

今日熱門文章 網友點擊推薦!