我的配置是Atlantic 6200繫列的在測試粉紅噪音用聲壓計,要把音量開到78(最大音量是98)才可以達到73db.之前用AT-1.也是,不知道是不是我的擴大機有問題左右聲道0中置0.環繞1.5低音3請問是什麼問題 謝謝
文章關鍵字

winsometang wrote:
我的配置是Atlan...(恕刪)


是會不同沒有錯啊..
位置,空間,喇叭效率不同,這些要調到相同音壓一定會不同的
把你這一套搬到我家去測量,又會不一樣的音壓
所以調整音壓的用意就是在這裡
把每支喇叭發出的音壓調整到一樣,所以才會有加減不同的數值
主要是在showroom聽的時候,音量只開到50就很大聲了,我的要開到78才可以達到thx75分貝的標準

winsometang wrote:
主要是在showro...(恕刪)


你的空間不小
但你去看的展示間有比你家大嗎?
要知道空間會影響喇叭的音壓
有空可以去查THX規範
況且你怎知道店家是不是有去調什麼
通常增加擴大機內的dB值那個地方的數值
喇叭就會變大聲

或真的不會調的話
花點錢請人來調音吧!
果然是個爛地方
Denon系統不熟悉
我integra 50.3 AT6200
音量開-24db可得75db(最大應該是+10or+20吧 沒試過)
主喇叭-3 中置-1 環繞-7 重低音-3
提供給樓主參考一下
我的是音量開到-24db用聲壓計測試只有51.4db.喇叭Tone test 設置FL-1.0 FR-0.5 中置-2.0左環繞-0.5又右環繞0低音-4.0音量要開到+0.5db聲壓才會到75db。應該不正常吧
winsometang wrote:
我的是音量開到-24...(恕刪)

小弟的做法是先用Audyssey跑過一次後先把主音量開到0dB(對於訊源不作放大也不做衰減)後再進喇叭Tone test用音壓計設定為A加權個別測試每隻喇叭的音壓是否為75dB如果不足或過量再用喇叭個別音量增益去做細調!!
謝謝樓上各位了,終於調好了,但是找到一篇文章關於麥克風擺位Audyssey MultEQ xt32測試的不知道效果如何

http://www.hometheatershack.com/forums/audio-processing/68407-audyssey-multeq-faq-setup-guide.html#post622330
Specifically relative to the example you quoted:
PLP center means the center of head point at the Primary Listening Position. Then the other measurement points are relative to that point. The directions are from the perspective of a person seated at that Listening Position.
The 2nd measurement point is 3 inches forward (toward the front of the room) from the PLPC point.
The 3rd measurement point is 3 inches up above the PLPC point.
The 4th measurement point is 3 inches up above and 3 inches forward from the PLPC point.
The 5th measurement point is 3 inches left of the PLPC point.
The 6th measurement point is 3 inches right of the PLPC point.
The 7th measurement point is 6 inches left of the PLPC point.
The 8th measurement point is 6 inches right of the PLPC point.


Read more: http://www.hometheatershack.com/forums/audio-processing/68406-audyssey-multeq-faq-setup-guide-discussion-thread.html#ixzz30sAo1BSm
文章分享
評分
評分
複製連結

今日熱門文章 網友點擊推薦!